ABB DP ADAPTER RPBA-01 KIT PROFIBUS Module for Drive New Original
in stock
Description of RPBA-01
The RPBA-01 PROFIBUS DP Adapter module is one of the optional
fieldbus adapter modules available for ABB drives. The RPBA-01 is a
device through which an ABB drive is connected to a PROFIBUS
network.
The drive is considered as a slave on the PROFIBUS network. Through
the RPBA-01 PROFIBUS DP Adapter module, it is possible to:
1.Give control commands to the drive (Start, Stop, Run enable,
etc.)
2.Feed a motor speed or torque reference to the drive
3.Give a process actual value or a process reference to the PID
controller of the drive
4.Read status information and actual values from the drive
5.Change drive parameter values
6.Reset a drive fault.
The PROFIBUS commands and services supported by the RPBA-01
PROFIBUS DP Adapter module are discussed in the chapters DP-V0
communication and DP-V1 communication.
Please refer to the user documentation of the drive as to which
commands are supported by the drive.
The adapter module is mounted into an option slot on the motor
control board of the drive. See the Hardware Manual of the drive
for module placement options.
Enclosure
Mounting:
Into the option slot on the control board of the drive.
Degree of protection: IP20
Ambient conditions:
The applicable ambient conditions specified for the drive in its
Hardware Manual are in effect.
Hardware settings:
1.Rotary switches for node address selection (address range 00 to
99)
2.DIP switch for bus termination selection
Software settings:
1.Input/Output/User Parameter data/Diagnostics format
2.Maximum cyclic I/O data size: 28 bytes in, max 28 bytes out, max.
56 bytes total
3.Maximum acyclic I/O data size: 240 bytes in, max. 240 bytes out,
max. 480 bytes total
4.Maximum User Parameter data/Diagnostics length: 26 bytes
Connectors:
1.34-pin parallel bus connector
2.9-pin female DSUB connector
Current consumption:
350 mA max. (5 V), supplied by the control board of the drive
General:
1.Estimated min. lifetime: 100 000 h
2.All materials UL/CSA-approved
3.Complies with EMC standards EN 50081-2 and EN 50082-2
Some Communications Modules
| Model No. | Protocol | Master or slave |
| CI801 | PROFIBUS DP-V1 | Slave |
| CI840A | PROFIBUS DP-V1 | Slave |
| CI853 | COMLI and MODBUS RTU | Master / Slave |
| CI854B | PROFIBUS DP-V1 | Master |
| CI855 | ABB's MasterBus 300 | Master |
| CI856 | ABB's S100 I/O | Master |
| CI857 | ABB's INSUM | Master |
| CI858 | ABB's DriveBus | Master |
| CI860 | FOUNDATION Fieldbus HSE | Master / Slave |
| CI865 | ABB's Satt I/O | Master |
| CI867 | MODBUS TCP | Master / Slave |
| CI868 | IEC 61850 | Master / Slave |
| CI869 | ABB's Advant Fieldbus 100 | Slave |
| CI871 | PROFINET IO | Master |
| CI873 | EtherNet IP / DeviceNet | Master |
| TB820V2 | ABB's Modulebus | Slave |
| TB825 (Multi Mode) | ABB's Modulebus | Slave |
| TB826 (Single Mode) | ABB's Modulebus | Slave |
| TB840A | ABB's Modulebus | Slave |
| TB842 | ABB's Modulebus | Not Applicable |
| TU807 | ABB's Modulebus | Not Applicable |
| TU840 | ABB's Modulebus | Not Applicable |
| TU841 | ABB's Modulebus | Not Applicable |
| TU846 | ABB's Modulebus | Not Applicable |
| TU847 | ABB's Modulebus | Not Applicable |
| TU848 | ABB's Modulebus | Not Applicable |
| TU849 | ABB's Modulebus | Not Applicable |
Some ABB items sold by WTL:
Liability:
WTL is not liable for any personal injury or property damage
resulting from the use of this equipment. It is
buyer's responsibility as to the safe handling & operation of this
equipment and to verify equipment is
compliance to their machinery.
Our Brands:
| 【Honeywell】 | Module DCS/PLC/Transmitter |
| 【Emerson/Delta V】 | Module/ CT Motor & Drives |
| 【ABB】 | I/O Module |
| 【AB】 | Module&Touch Screen |
| 【Rosemount】 | Transmitter |
| 【Yokogawa】 | Transmitter |
| 【Yaskawa】 | Servo Drive&Servo Motor |
| 【GE/Fanuc】 | IC69 Series PLC |
| 【Mitsubishi】 | Servo Drive&Servo Motor |
(Modicon,SMC,SICK,NORGREN,Siemens,Ebmpapst etc.)
Company Introduction:
