YASKAWA AC SERVO MOTOR SGMAV-02A3A2C 3phase 0.318N.m Industrial
Servo Motor
SEPCIFICATIONS
| Brand | Yaskawa |
| Model | SGMAV-02A3A2C |
| Output | 100W |
| Max Torque | 0.637Nm |
| Rated Speed | 3000 1/min |
| Max Current | 0.91A |
SIMILAR PRODUCTS
| SGMAV-10A3A21 | SGMAV-10A3A2C |
| SGMAV-10A3A61 | SGMAV-A5ADA21 |
| SGMAV-A5ADAH101 | SGMAV-C2A3A61 |
| SGMAV-C2ADA61 | SGMCS-02B3C11 |
| SGMCS-02B3C4 | SGMCS-04B3C11 |
| SGMCS-04C3B11 | SGMCS-05B3C11 |
| SGMCS-07B3B11 | SGMCS-07B3C11 |
| SGMCS-08DDA-TE12 | SGMCS-17D3A-MB11 |
| SGMCS-17D3C11 | SGMCS-35E3A-MB11 |
| SGMAV-08A3A21 | SGMCS-80M3A11 |
OTHER SUPERIOR PRODUCTS
| Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
| Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
| Honeywell TC-,TK- | GE Modules IC - |
| Fanuc motor A0- | Yokogawa transmitter EJA- |
Contact person: Anna
E-mail: wisdomlongkeji@163.com
Cellphone: +0086-13534205279
High power AC motors are typically inductive in design. An
inductive rotor is constructed by laminating iron disks together to
form the central core of the rotor. Slots around the circumference
of the core receive conductors, termed ‘rotor bars’ which are
shorted together at either end of the rotor. This is accomplished
by ‘end rings’ which may be welded to the ends of the rotor bars,
or the end rings and rotor bars may be injection molded around the
core, effectively forming a single, homogenous structure.
When the rotor is assembled inside of the stator, current flow
through the stator windings generates corresponding ‘induced’
current flow through nearly aligned, adjacent rotor bars. This
current path is completed by the end rings, creating a closed
circuit. The induced current flow generates magnetic force in the
rotor, compelling it to rotate to keep the stator and rotor fields
aligned. The greater the misalignment, the greater the induced
current and therefore the higher the electromotive force (emf)
and torque generated.
Always follow the specified installation method.
The Servopack generates heat. Install the Servopack so that it can
radiate heat freely. Note also that the Servopack must be in an
environment free from condensation, vibration and shock.
Perform noise reduction and grounding properly.
If the signal line is noisy, vibration or malfunction will result.
- Separate high-voltage cables from low-voltage cables.
- Use cables as short as possible.
- Use at least class 3 grounding (ground resistance 100Ω or below)
for the Servomotor and Servopack.
- Never use a line filter for the power supply in the motor circuit.
Conduct a voltage resistance test under the following conditions.
- Voltage: 1,500 Vrms AC, one minute
- Braking current: 20 mA
- Frequency: 50/60 Hz
- Voltage applied point: Between R, T terminals and frame ground
(connect terminals R and T securely.)
Use a fast-response type ground-fault interrupter.
For a ground-fault interrupter, always use a fastresponse type or
one designed for PWM inverters. Do not use a time-delay type.
Do not perform continuous operation under overhanging load.
Continuous operation cannot be performed by rotating the motor from
the load and applying regenerative braking. Regenerative braking by
the Servopack can be applied only for a short period, such as the
motor deceleration time.
The Servomotor cannot be operated by turning the power ON and OFF.
Frequently turning the power ON and OFF causes the internal circuit
elements to deteriorate. Always start or stop the servomotor by
using reference pulses.
