Efficiency Industrial Servo Drives Yaskawa servopack SGDL-02AP 200W
Input AMPS4.0
Quick Details
Brand Name:Yaskawa
Model Number:SGDL-02AP
Input Voltage:200-230V
Input AMPSt: 4.0
Input Frequency:50/60HZ
Input PH : 1
Series : Sigma 2 (Σ-II Series)
Output Power : 200W
Output Voltage: 0-230V
Output AMPS: 2.0
Output Frequency:0-300Hz
Output PH :3
Temperture: 0-55℃
Place of Origin:Japan
Efficiency:IE 1
OTHER SUPERIOR PRODUCTS
Yasakawa Motor, Driver SG- Mitsubishi Motor HC-,HA-
Westinghouse Modules 1C-,5X- Emerson VE-,KJ-
Honeywell TC-,TK- Fanuc motor A0-
Rosemount transmitter 3051- Yokogawa transmitter EJA-
Contact person: Anna
E-mail: wisdomlongkeji@163.com
Cellphone: +0086-13534205279
Similar Products
| SGDL-02AP |
| SGDL-02AP+SGML-02AF14 |
| SGDL-02AS |
| SGDL-03BP |
| SGDL-04AP |
| SGDL-04AP+SGML-04AF14 |
| SGDL-04AP+SGML-04AF14 |
| SGDL-04AS |
| SGDL-04SVS |
| SGDL-08AF12 |
| SGDL-08AP |
| SGDL-08AP+SGML-08AF14 |
| SGDL-A5BP |
| SGDM-01AD |
| SGDM-01ADA |
| SGDM-01ADA/SGDH-01AE+SGMAH-01AAA21 |
| SGDM-01ADA+SGMAH-01AAAG761 |
| SGDM-01ADA-RY5 |
| SGDM-01BDA |
| SGDM-02ADA |
| SGDM-02ADA/SGDH-02AE+SGMAH-02AAA21 |
| SGDM-02ADA+SGMAH-02AAA2C |
| SGDM-02ADA+SGMPH-02AAA41 |
| SGDM-02ADA+SGMPH-02A1A21 |
| SGDM-02AD-R |
| SGDM-02BDA |
The main circuit positive-side terminal is only available to use at
three-phase 200 VAC, 6 kW SERVOPACK.
Do not use 1 or 2.
Be sure to disconnect the lead between B2 and B3, before connecting
an external regenerative registor to the SERVOPACK.
For connecting a DC reactor, refer to 6.4.8 DC Reactor for Harmonic
Suppression.
Molded-case circuit breaker (MCCB)
Power supply
Three-phase 200 VAC
Protects the power supply line by shutting the circuit OFF when
overcurrent is detected.(Refer to 5.8.9.)
Used to eliminate external noise from the power line.(Refer to
5.8.10.)
Regenerative resistor
Connect an external regenerative resistor to terminals B1 and B2 if
the regenerative capacity is insufficient.
(Refer to 5.8.6.)
* 1. Nominal value at the rated load. The specified derating is
required to select an appropriate fuse capacity.
* 2. Cutoff characteristics (25°C): 300% five seconds min. and
inrush current of 20ms
* 3. A preventive circuit for inrush current is not built in the 24
VDC control power supply. The protective circuit must be designed
by the customer.
* 4. Make sure the current capacity is accurate. For the SERVOPACK
with the cooling fan builtin, an inrush current flows; 200 % of the
current capacity in the table above for two seconds, when turning
ON the control circuit power supply to start the fan working. Note:
Do not use a fast-acting fuse. Because the SERVOPACK’s power supply
is a capacitor input type, a fast-acting fuse may blow when the
power is turned ON.
CAUTION
• Conduct trial operation on the servomotor alone with the motor
shaft disconnected from machine to avoid
any unexpected accidents.
Failure to observe this caution may result in injury.
• Before starting operation with a machine connected, change the
settings to match the parameters of the
machine.
Starting operation without matching the proper settings may cause
the machine to run out of control or malfunction.
• Forward run prohibited (P-OT) and reverse run prohibited (N-OT)
signals are not effective during zero point
search mode using parameter Fn003.
• When using the servomotor for a vertical axis, install the safety
devices to prevent workpieces to fall off due
to occurrence of alarm or overtravel. Set the servomotor so that it
will stop in the zero clamp state at
occurrence of overtravel.
Failure to observe this caution may cause workpieces to fall off
due to overtravel.
• When not using the normal autotuning, set to the correct moment
of inertia ratio.
Setting to an incorrect moment of inertia ratio may cause
vibration.
• Do not touch the SERVOPACK heatsinks, regenerative resistor, or
servomotor while power is ON or soon
after the power is turned OFF.
Failure to observe this caution may result in burns due to high
temperatures.
• Do not make any extreme adjustments or setting changes of
parameters.
Failure to observe this caution may result in injury due to
unstable operation.
• When an alarm occurs, remove the cause, reset the alarm after
confirming safety, and then resume operation.
Failure to observe this caution may result in injury.
• Do not use the servo brake of the servomotor for ordinary
braking.
Failure to observe this caution may result in malfunction.
