PLC Programmable Logic Controller GE FANUC IC660CBB903K Series Six
BUS CONTROLLER
This GE Fanuc IC660CBB903G BUS Control Module without Diagnostics
is new from surplus stock. This unit ships in the manufacturer's
original packaging with standard documentation and accessories.
Accessories Include:
• 44A713909-003: 150 Ohm Bus Terminating Plug
• 44A713909-004: 75 Ohm Bus Terminating Plug
• GFK-0171: Series Six Bus Controller Manual
• GEK-90486: Genius I/O System Manual
• GFK-0025A: Genius I/O System Bus Controller Datasheet
QUICK DETAILS
- Brand :GE
- Model : IC660CBB903K
- Place of Origin : USA
Features
- Interfaces Genius I/O Serial Bus to Series Six Plus Controller
- Provides Channel Selection for Expanded I/O Addressing
- 4-Segment DIP Switch
DESCRIPTION
The GE Fanuc IC660CBB90xx Series BUS Control Modules are a required
interface between a Series Six Plus PLC and the Genius I/O blocks
when they are included in the PLCs I/O system. The Bus Controller
module can be placed in any I/O slot in the CPU or in a
high-capacity I/O rack located in a CPU station or Local I/O
station up to 2000 feet (600 meters) from the CPU. Multiple Bus
Controllers can be placed in one rack. Since each Bus Controller
consumes 20 units of load, up to 5 modules can be placed in a CPU
rack, or 10 modules in a high capacity I/O rack.
A Bus Controller can be placed in an I/O rack in a Remote I/O
station if the CPU scan time is greater than 10 ms. However,
because of the reduced capacity of the serial I/O communications
link, window commands would not be supported. Each Bus Controller
can interface up to 30 Genius I/O blocks to the Series Six Plus CPU
by twisted pair communications up to 2000 feet (600 meters). The
only limit to the number of Bus Controllers in any one PLC system
is the l/O capacity of the Series Six Plus CPU. Each Bus
Controller, similar to any I/O module, has access to all l/O
references on its I/O chain.
A 4-segment DIP switch located on the module is used to enable
channel selection for Expanded I/O addressing. If Normal
(non-expanded) addressing is used or if channel selection is made
through I/O Transmitter Modules, no switch setting is necessary.
The Genius I/O bus must be terminated at the Bus Controller by its
characteristic impedance. The enhanced version Bus Controller
provides three selectable on-board impedances, 100Ω, 150Ω, or 750Ω.
Three jumpers (JPI, JP2, and JP3) on the module are used to select
one of the listed values, or to select no impedance.
Product Family: IC660CBB903G, IC660CBB903H, IC660CBB903K,
IC660CBB903, IC660CBB902, IC600CBB902G, IC600 CBB902G,
IC600-CBB902G, IC600CBB902H, IC600 CBB902H, IC600-CBB902H Genius
I/O, Series Six
Important Notice: Please note that any additional items included with this
equipment such as accessories, manuals, cables, calibration data,
software, etc. are specifically listed in the above stock item
description and/or displayed in the photos of the equipment. Please
contact one of our Customer Support Specialists if you have any
questions about what is included with this equipment or if you
require any additional information.
OTHER SUPERIOR PRODUCTS
| Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
| Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
| Honeywell TC-,TK- | GE Modules IC - |
| Fanuc motor A0- | Yokogawa transmitter EJA- |
Contact person: Anna
E-mail: wisdomlongkeji@163.com
Cellphone: +0086-13534205279
